DIY Transistor Amp Using NVA Boards

For the three and more legged things
Post Reply
User avatar
Dave the bass
Amstrad Tower of Power
Posts: 12273
Joined: Tue May 22, 2007 4:36 pm
Location: NW Kent, Darn Sarf innit.

#91 Re: DIY Transistor Amp Using NVA Boards

Post by Dave the bass »

Ooo errr.

Where did the smoke come from Steve? If it was me I'd check TX phase and rectifiers.
"The fat bourgeois and his doppelganger"
User avatar
pre65
Amstrad Tower of Power
Posts: 21373
Joined: Wed Aug 22, 2007 11:13 pm
Location: North Essex/Suffolk border.

#92 Re: DIY Transistor Amp Using NVA Boards

Post by pre65 »

Dave the bass wrote: Sat Jan 18, 2020 8:06 pm Ooo errr.

If it was me I'd check TX phase
Many years ago I had transformer smoke and TX phase was the problem.
The only thing necessary for the triumph of evil is for good men to do nothing.

Edmund Burke

G-Popz THE easy listening connoisseur. (Philip)
User avatar
Nick
Site Admin
Posts: 15708
Joined: Sun May 06, 2007 10:20 am
Location: West Yorkshire

#93 Re: DIY Transistor Amp Using NVA Boards

Post by Nick »

then smoke wisps
Where from?
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
User avatar
Nick
Site Admin
Posts: 15708
Joined: Sun May 06, 2007 10:20 am
Location: West Yorkshire

#94 Re: DIY Transistor Amp Using NVA Boards

Post by Nick »

If the caps are metal cased, make sure they are isolated from the chassis as the -ve terminal will be connected to the can of the transformer (this has caught me out before).
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#95 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

Thanks for the suggestions guys. The smoke came from the on off switch, just a small wisp. That was enough to trigger a hurried switch-off. I’ll have a look tomorrow.
Sgt. Baker started talkin’ with a Bullhorn in his hand.
User avatar
pre65
Amstrad Tower of Power
Posts: 21373
Joined: Wed Aug 22, 2007 11:13 pm
Location: North Essex/Suffolk border.

#96 Re: DIY Transistor Amp Using NVA Boards

Post by pre65 »

Cressy Snr wrote: Sat Jan 18, 2020 11:49 pm Thanks for the suggestions guys. The smoke came from the on off switch, just a small wisp. That was enough to trigger a hurried switch-off. I’ll have a look tomorrow.
I've wired up DP on/off switches incorrectly in the past. :oops: :oops:
The only thing necessary for the triumph of evil is for good men to do nothing.

Edmund Burke

G-Popz THE easy listening connoisseur. (Philip)
steve s
Shed dweller
Posts: 2829
Joined: Wed May 30, 2007 6:19 pm
Location: east yorks

#97 Re: DIY Transistor Amp Using NVA Boards

Post by steve s »

I'm sure will soon get the issue sorted Steve
You would think relatively simple solid state would be easy after valve amps.. but my first chip amp is going pretty crap... a simple tda 2030, but it just loves to ossilate.. after a month I still can't plug anything into it ! Although it seems ok untill I wave the phono cable anywhere near it
Best of luck..
Last edited by steve s on Sun Jan 19, 2020 1:00 pm, edited 1 time in total.
The tube manual is quite like a telephone book. The number of it perfect. It is useful to make it possible to speak with a girl. But we can't see her beautiful face from the telephone number
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#98 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

steve s wrote: Sun Jan 19, 2020 12:17 pm I'm sure will soon get the issue sorted Steve
You would think relatively simple solid state would be easy after valve amps.. but my first chip amp is going pretty crap... a simple tda 2030, but it just loves to ossilate.. after a month I still can't plug anything into it ! Although it seems ok untill I wave the phone cable anywhere near it
Best of luck..
Yes, SS at the moment, is a royal PITA . When Richard sent me the boards, he told me, in his email, that he wanted to see a valve bloke, try and do a transistor amp, and that he knew he would be p*ssing himself laughing at my attempts to get his boards going.
He’s definitely up there laughing at the moment. :)

The b’stards aren’t going to beat me. Where’s a bleed’n variac when you need one.
Sgt. Baker started talkin’ with a Bullhorn in his hand.
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#99 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

Nick wrote: Sat Jan 18, 2020 10:50 pm If the caps are metal cased, make sure they are isolated from the chassis as the -ve terminal will be connected to the can of the transformer (this has caught me out before).
Here was the problem:
5788A691-7E69-4301-BFF5-A9ABC68637EB.jpeg
Sharp edge on the inside of one of the cap clamps on the larger power supply, had cut through the plastic insulation, and caused a high resistance ground fault to the earthed chassis, via the can of the offending cap. Sod’s Law of course ensured that said cap just happened to have its negative terminal as the power feed, with its positive as 0V.
This must have been enough of a short, to pull excessive current through the large transformer. Anyway I’ve replaced the whole rectifier/transformer/capacitor network, plus I threw away the offending cap clamp, and everything fires up properly without incident.

Now we can put in the wires to the boards etc.
Last edited by Cressy Snr on Sun Jan 19, 2020 4:00 pm, edited 1 time in total.
Sgt. Baker started talkin’ with a Bullhorn in his hand.
User avatar
Dave the bass
Amstrad Tower of Power
Posts: 12273
Joined: Tue May 22, 2007 4:36 pm
Location: NW Kent, Darn Sarf innit.

#100 Re: DIY Transistor Amp Using NVA Boards

Post by Dave the bass »

Well done on finding the problem Steve.
"The fat bourgeois and his doppelganger"
User avatar
pre65
Amstrad Tower of Power
Posts: 21373
Joined: Wed Aug 22, 2007 11:13 pm
Location: North Essex/Suffolk border.

#101 Re: DIY Transistor Amp Using NVA Boards

Post by pre65 »

Dave the bass wrote: Sun Jan 19, 2020 3:48 pm Well done on finding the problem Steve.
Yes, well done Steve.

I prefer to use non metallic capacitor clamps if possible.
The only thing necessary for the triumph of evil is for good men to do nothing.

Edmund Burke

G-Popz THE easy listening connoisseur. (Philip)
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#102 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

Thanks chaps.

It’s non metallic clamps for me from now on.

Power supply all done; double pole switching (with fuse in the live side of course)
Chassis divider repositioned to serve as a heat shield between caps and heat sinks.
858ACBBA-6C13-47B5-8F76-324AEC5FC264.jpeg
Sgt. Baker started talkin’ with a Bullhorn in his hand.
User avatar
Mike H
Amstrad Tower of Power
Posts: 20157
Joined: Sat Oct 04, 2008 5:38 pm
Location: The Fens
Contact:

#103 Re: DIY Transistor Amp Using NVA Boards

Post by Mike H »

Cressy Snr wrote: Sun Jan 19, 2020 3:08 pm
Nick wrote: Sat Jan 18, 2020 10:50 pm If the caps are metal cased, make sure they are isolated from the chassis as the -ve terminal will be connected to the can of the transformer (this has caught me out before).
Here was the problem:

Image

Sharp edge on the inside of one of the cap clamps on the larger power supply, had cut through the plastic insulation, and caused a high resistance ground fault to the earthed chassis, via the can of the offending cap.
Image

Image

Anyhow, that's alright then!

:thumbleft:
 
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#104 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

The story so far:
02F35BE6-0980-4F87-ADD3-556DD863DB68.jpeg
Just the power rails and the input socket wiring to install, then it’ll be switch-on, shortly followed by...KERBLAMMM!, then :sad2:...cough..splutter..then...”darling, where’s the dustpan and brush? ...No....don’t come in the kitchen just yet!”....”I know there’s a draught; I’ve got the back door open!” then.... “feck it I’ll stick with valves” :lol:
Sgt. Baker started talkin’ with a Bullhorn in his hand.
Cressy Snr
Amstrad Tower of Power
Posts: 10552
Joined: Wed May 30, 2007 12:25 am
Location: South Yorks.

#105 Re: DIY Transistor Amp Using NVA Boards

Post by Cressy Snr »

Board wiring and inputs all done:
874D6C1E-98DE-4B5B-945E-4FC2099F1B44.jpeg
Sgt. Baker started talkin’ with a Bullhorn in his hand.
Post Reply