Adventures in LCR Phonos
-
- Thermionic Monk Status
- Posts: 5651
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#1 Adventures in LCR Phonos
This is going to be a bit of a long running project I think.
I was inspired by hearing Shaman's (hello Nigel!) DIYHiFiSupply Cole LCR at Steve's t'other weekend, there was a "rightness" that stood out. Nick lent me his S&B 600R LCRs at Owston on Saturday, so there's no going back!
Phonos, and LCR phonos especially, are finicky things so I reckon the place to start is the Cole, not least because I think it used the same S&B LCRs, I probably have most of the bits, the circuit's available, and I have an idea of what it should sound like.
http://www.store.diyhifisupply.com/cole ... q=node/827
The Cole isn't produced anymore, but I did email Brian Cherry and DIYHiFiSupply to check a couple of details but didn't get a response. Nick's sensible advice is to keep it simple,and my first thoughts are to bin the crazy looking B+ PS. I've some Salas Simplistic Mosfet High Voltage Shunt (SSHV2) kits I've been wanting to use for quite a while so this looks like a decent place to start.
http://www.diyaudio.com/forums/power-su ... -regs.html
Don't hold your breathe for rapid progress!
I was inspired by hearing Shaman's (hello Nigel!) DIYHiFiSupply Cole LCR at Steve's t'other weekend, there was a "rightness" that stood out. Nick lent me his S&B 600R LCRs at Owston on Saturday, so there's no going back!
Phonos, and LCR phonos especially, are finicky things so I reckon the place to start is the Cole, not least because I think it used the same S&B LCRs, I probably have most of the bits, the circuit's available, and I have an idea of what it should sound like.
http://www.store.diyhifisupply.com/cole ... q=node/827
The Cole isn't produced anymore, but I did email Brian Cherry and DIYHiFiSupply to check a couple of details but didn't get a response. Nick's sensible advice is to keep it simple,and my first thoughts are to bin the crazy looking B+ PS. I've some Salas Simplistic Mosfet High Voltage Shunt (SSHV2) kits I've been wanting to use for quite a while so this looks like a decent place to start.
http://www.diyaudio.com/forums/power-su ... -regs.html
Don't hold your breathe for rapid progress!
#2 Re: Adventures in LCR Phonos
That Cole certainly made an impression eh simon!
#3 Re: Adventures in LCR Phonos
I have my doubts about the second ecc88 in grid leak mode, but it will do no harm to start there.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
#4 Re: Adventures in LCR Phonos
I would also check if thats using the S&B riaa, it assumes there is no path to ground from the input and the caps in there are good for 65v.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
#5 Re: Adventures in LCR Phonos
I would ditch the grid leak bias, that big resistor is a potential source of hum noise, and as the 88 ages it may runaway, especially if you replace the 88 with something with more GM, like D3A.
By all means try it as is, but be prepared to chase hum. This is one of those times when a bigger cap and a smaller resistor isn't a bad thing.
Andrew
By all means try it as is, but be prepared to chase hum. This is one of those times when a bigger cap and a smaller resistor isn't a bad thing.
Andrew
Analogue, the lost world that lies between 0 and 1.
- izzy wizzy
- Old Hand
- Posts: 1496
- Joined: Fri Nov 02, 2007 7:02 pm
- Location: Auckland NZ
- Contact:
#7 Re: Adventures in LCR Phonos
It looks like Thorsten Loesch designed the Cole or had a hand in it.
He used the S&B LCR in his own http://www.izzy-wizzy.com/audio/phono/T ... nal6xz.gif
He started in another direction earlier in its design http://www.izzy-wizzy.com/audio/phono/T ... 0026xz.gif
These cover both choices: drive with 600R, load lightlty OR drive from high Z, load with 600R
He liked grid leak bias. In the Cole, the 2nd stage has a cathode resistor which might help with runaway.
cheers,
Stephen
He used the S&B LCR in his own http://www.izzy-wizzy.com/audio/phono/T ... nal6xz.gif
He started in another direction earlier in its design http://www.izzy-wizzy.com/audio/phono/T ... 0026xz.gif
These cover both choices: drive with 600R, load lightlty OR drive from high Z, load with 600R
He liked grid leak bias. In the Cole, the 2nd stage has a cathode resistor which might help with runaway.
cheers,
Stephen
-
- Thermionic Monk Status
- Posts: 5651
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#8 Re: Adventures in LCR Phonos
I've looked at the curves for the ECC88 and I struggled to get my head round the likely OPs. Think I might have said on Saturday? With just 65V on both anodes the different cathode resistors don't make much sense from a current POV.
-
- Thermionic Monk Status
- Posts: 5651
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#9 Re: Adventures in LCR Phonos
According to the BOM on the link above they were S&B 600R units.
Can you explain a bit more what you mean by no path to ground from the input?
-
- Thermionic Monk Status
- Posts: 5651
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#10 Re: Adventures in LCR Phonos
Good points well made.Andrew wrote: ↑Tue Jul 03, 2018 4:12 pm I would ditch the grid leak bias, that big resistor is a potential source of hum noise, and as the 88 ages it may runaway, especially if you replace the 88 with something with more GM, like D3A.
By all means try it as is, but be prepared to chase hum. This is one of those times when a bigger cap and a smaller resistor isn't a bad thing.
Andrew
I was having a look around Dave Slagle's forum earlier and found a thread that you Nick Mark and James posted on. I've only read the start of it but there were interesting discussions about pentodes and Aikidos. More reading to do.
Come on England!
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#11 Re: Adventures in LCR Phonos
Oh dear, I wonder what I posted on that ... !
Thanks for reminding me about that football match. I was up having a bath and had forgotten.
Thanks for reminding me about that football match. I was up having a bath and had forgotten.
"Once you find out ... the Circumstances ; then you can go out"
#12 Re: Adventures in LCR Phonos
If you look at he circuit of the tango LCR, there is a resistive path from the input to the ground point. If you put 65v (as that circuit does) with no blocking cap then current will flow. May be ok, may not, can't say. You can check with a multimeter between the input and ground to see what the resistance is.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- izzy wizzy
- Old Hand
- Posts: 1496
- Joined: Fri Nov 02, 2007 7:02 pm
- Location: Auckland NZ
- Contact:
#13 Re: Adventures in LCR Phonos
LCR modules come in 3 varieties. Some with a path to ground from theinput and some not
-
- Thermionic Monk Status
- Posts: 5651
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#14 Re: Adventures in LCR Phonos
Thanks Stephen, the last attachment was particularly helpful. And as far as I know Thorsten designed the Cole.
#15 Re: Adventures in LCR Phonos
I have an all-valve balanced LCR phono stage built by a friend. I'll bring it along to a meet some time.
EDIT - I may have missed the point of this thread. I'll get me coat.
EDIT - I may have missed the point of this thread. I'll get me coat.
Last edited by RhythMick on Wed Jul 04, 2018 8:52 am, edited 1 time in total.