Nice amp - whilst looking at the transformer covers - obviously cut by laser or a profile cutter - I was thinking of the Shaper Origin - sort of thing that would make that so much easier... (at a cost).Ray P wrote: ↑Mon Dec 18, 2017 9:43 pm Hi Dave, I dunno whether this will inspire you or distract you but this is a pretty neat Beast project...
http://sharksphotos.yolasite.com/
Dieselpunk Preamp of Doom and the Beast with Two Backs
- jack
- Thermionic Monk Status
- Posts: 5502
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#151 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Vivitur ingenio, caetera mortis erunt
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#152 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Came across a particularly evil bug in my CAD software yesterday - you're always told to save your work regularly and I do that as a matter of course, as the software is a little bit 'crashy' - especially as my version is several years old and I'm too tight / poor to upgrade to the latest. It does the job fine.
Last night, it rather charmingly decided to crash in the middle of a save - thereby completely corrupting the file and rendering it unrecoverable.
Luckily, because of a lot of recent significant changes, I've been incrementing the versions. I had in fact incremented an hour previously so I didn't lose too much work, but heck! The preamp design stayed at version 5.0 for quite some time and if that bug had surfaced with that file, we might not have a preamp in the rack right now. (I save to a drop box folder which auto-syncs to the cloud).
From now on I do "Save As..." and up the version number each time! I put this here as a cautionary tale for anyone doing similar work.
Last night, it rather charmingly decided to crash in the middle of a save - thereby completely corrupting the file and rendering it unrecoverable.
Luckily, because of a lot of recent significant changes, I've been incrementing the versions. I had in fact incremented an hour previously so I didn't lose too much work, but heck! The preamp design stayed at version 5.0 for quite some time and if that bug had surfaced with that file, we might not have a preamp in the rack right now. (I save to a drop box folder which auto-syncs to the cloud).
From now on I do "Save As..." and up the version number each time! I put this here as a cautionary tale for anyone doing similar work.
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- Mike H
- Amstrad Tower of Power
- Posts: 20189
- Joined: Sat Oct 04, 2008 5:38 pm
- Location: The Fens
- Contact:
#153 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
One word - "backups".
I have even saved a file with a changed name, just so the previous is a backup. But you've already figured that out.
Another method I sometimes use is have a sub-folder called "Backup", and put copies of files in there.
-
I have even saved a file with a changed name, just so the previous is a backup. But you've already figured that out.
Another method I sometimes use is have a sub-folder called "Backup", and put copies of files in there.
-
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#154 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
The CAD work for the Beasts is nearing completion, I just have to 'mirror image' the housing bracket layout and it'll be about done.
Here is how the mirror imaged pair are expected to look:
Here is how the mirror imaged pair are expected to look:
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#155 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Construction of the two monoblocks will require the fabrication of 18(!) panels in total. I have finished building the FPD (front panel designer) files for the first 16, outstanding are the two cream coloured top panels (where the valve sockets and transformers etc sit) with the 5mm inner diameter bend, that Schaeffer are going to do for me.
I added up the pricing just for those first sixteen and had to go and lie down in a darkened room!
I'm still trying to get out of Schaeffer what the bending allowance / K-factor figure is for the bend, so that I can plug it into CAD and generate an accurate map for the CNC machine. I sent them an email asking for this along with a CAD drawing of the bent panel so they'd have a picture of what I wanted - so far they've quoted me a cost including transferring the data from that CAD file to an FPD file - which I am perfectly capable of doing myself, all I need to know is the bending allowance!! Here's hoping I get the right answer soon....
I added up the pricing just for those first sixteen and had to go and lie down in a darkened room!
I'm still trying to get out of Schaeffer what the bending allowance / K-factor figure is for the bend, so that I can plug it into CAD and generate an accurate map for the CNC machine. I sent them an email asking for this along with a CAD drawing of the bent panel so they'd have a picture of what I wanted - so far they've quoted me a cost including transferring the data from that CAD file to an FPD file - which I am perfectly capable of doing myself, all I need to know is the bending allowance!! Here's hoping I get the right answer soon....
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
#156 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
I still think my posts around 2nd August are relevant. It would really pay to find a chap with a bending press.....Thermionic Idler wrote: ↑Fri Jan 12, 2018 3:44 pm
I added up the pricing just for those first sixteen and had to go and lie down in a darkened room!
There's nowhere you can be that isn't where you're meant to be
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#157 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
I got a local specialist in this sort of work to fabricate me the housing for the Pass F4 from 2.5mm aluminium. That cost about £200.
"Once you find out ... the Circumstances ; then you can go out"
#158 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
I got a local specialist in this sort of work to fabricate me the housing for the Pass F4 from 2.5mm aluminium. That cost about £200.
wowsa, I must just be lucky then........So far the F2,F4,F6,zen5 have cost me £20 in total for all the bottoms and backs. The fronts have all been 5mm offcuts and the tops I cut out of a full sheet of 50% 6mm perf 2mm thick, which I think cost about £50 delivered from ebay. So that's about £70 for 4 chassis.This obviously does not include the heatsinks or the 25mm equal angle...but, but....
These obviously won't look as shoddy as Mr Idler's and they are in bare aluminium finish....but I still think it's worth looking around for alternative methods......yeah, I know, I'm a cheapskate..
There's nowhere you can be that isn't where you're meant to be
- IslandPink
- Amstrad Tower of Power
- Posts: 10041
- Joined: Tue May 29, 2007 7:01 pm
- Location: Denbigh, N.Wales
#159 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
I wasn't trying to compete with you, Ed - I know better - as you're in Hull !
However I'll pick you up on counting offcuts as cost-free - that's cheating ! ( unless you found them in a skip )
I was overcharged for that chassis, just interested in what the number was that put Dave in a darkened room.
However I'll pick you up on counting offcuts as cost-free - that's cheating ! ( unless you found them in a skip )
I was overcharged for that chassis, just interested in what the number was that put Dave in a darkened room.
"Once you find out ... the Circumstances ; then you can go out"
#160 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
good point, well made!IslandPink wrote: ↑Fri Jan 12, 2018 6:20 pm I wasn't trying to compete with you, Ed - I know better - as you're in Hull !
I'm still working on the escape plan
There's nowhere you can be that isn't where you're meant to be
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#161 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
I think for now I'll just say "a lot". I think it'll be worth it though. These things are going to be in the living room next to each speaker - they have to look good as well as sound good.IslandPink wrote: ↑Fri Jan 12, 2018 6:20 pm I was overcharged for that chassis, just interested in what the number was that put Dave in a darkened room.
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#162 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Hooray - I finally got a number for the bending allowance. Now I can generate the remaining two FPD files and get a final cost...
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#163 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Slow progress of late but last week whilst snowed in, I worked on populating the main circuit boards.
Electrolytics are mostly high temp Panasonics, all fast recovery diodes (UF4007, FR605-T), 2W resistors are Vishay CPF series metal films rather than metal oxide, 0.5W are Takman metal films aside from a couple of positions where the specified value was unavailable, these have Vishay CMF's instead.
I have the signal coupling caps, T4 transformer and big smoothing caps left to populate. Hit a snag yesterday, I had bought ClarityCap ESA's to go in the C13, C14, C17 and C18 positions. Unfortunately, I discovered two problems: 1) the leadouts on the 0.47uF cap were 1mm solid core, which was just that little bit too big to go through the PCB hole. That could probably have been kludged around but 2) checking the ESA datasheets revealed they were only rated to 70C, and I wanted everything in here to be rated to at least 100C for long life.
I've emailed HiFi Collective to see if I can exchange them for AMCO Amtrans caps as they cost about the same, are rated to 100C and will fit perfectly into the available PCB space. I already have one in the C16 position (on the cathode of the positive 12BH7 driver valve), next to Z6. Just hoping the 20% tolerance on these won't be a problem (I don't think it will be).
Electrolytics are mostly high temp Panasonics, all fast recovery diodes (UF4007, FR605-T), 2W resistors are Vishay CPF series metal films rather than metal oxide, 0.5W are Takman metal films aside from a couple of positions where the specified value was unavailable, these have Vishay CMF's instead.
I have the signal coupling caps, T4 transformer and big smoothing caps left to populate. Hit a snag yesterday, I had bought ClarityCap ESA's to go in the C13, C14, C17 and C18 positions. Unfortunately, I discovered two problems: 1) the leadouts on the 0.47uF cap were 1mm solid core, which was just that little bit too big to go through the PCB hole. That could probably have been kludged around but 2) checking the ESA datasheets revealed they were only rated to 70C, and I wanted everything in here to be rated to at least 100C for long life.
I've emailed HiFi Collective to see if I can exchange them for AMCO Amtrans caps as they cost about the same, are rated to 100C and will fit perfectly into the available PCB space. I already have one in the C16 position (on the cathode of the positive 12BH7 driver valve), next to Z6. Just hoping the 20% tolerance on these won't be a problem (I don't think it will be).
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
#164 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
Do you expect the inside to get above 70C ?
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
- Thermionic Idler
- Old Hand
- Posts: 1018
- Joined: Sun Apr 22, 2012 8:22 pm
- Location: Southsea
#165 Re: Dieselpunk Preamp of Doom and the Beast with Two Backs
It shouldn't get that high, at a guess maybe mid 50's at the very most on a hot day? The idle heat should be about 240 watts a side with a 12 tube configuration (it can be reduced to 8 tube / 175 watts in the summer). It's more that I wanted to ensure a good wide margin between the rated and actual running temperatures so that the components would last longer. Probably overkill, but I'm all about the over-engineering!
Deck: Garrard 301 - Audio Origami PU7 - NW Analogue DH3S
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets
Phono: Pete Millett LR, Lundahl SUT, AMB σ22 PSU
Linestage: Bruno Putzeys Balanced Pre + Hans Polak relay mod, LCDuino control
Power amps: 300B PP 'Symmetric Reichert'
Speakers: FF225WK Big Mets