MJ Statistical Regulator PCBs
-
- Thermionic Monk Status
- Posts: 5600
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#121 Re: MJ Statistical Regulator PCBs
Thanks Nick, I think I understand. What threw me was the 200mA max. These aren't the regs for an output stage biased at 80mA hoping it will happily vary between 0mA and 160mA (plus the 15mA through the zeners). What it's really intended for is a screen bias for instance, or perhaps a preamp or pre stage, in which case you're not going to be bothered about 200mA max. Right?
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#122 Re: MJ Statistical Regulator PCBs
Absolutely. Screen supplies and preamps is where its at.
Anywhere where signal levels are low and s/n needs to be managed carefully. It's a neglected area...
Anywhere where signal levels are low and s/n needs to be managed carefully. It's a neglected area...
Vivitur ingenio, caetera mortis erunt
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#123 Re: MJ Statistical Regulator PCBs
With bulk purchases, excluding P&P, I've got the cost (including VAT) down to £15.00 for each full kit and £9.00 for each expansion board.
P&P within the UK is £1.50 for each multiple of 4 boards of any type (or part thereof), e.g. 2 kits + 2 expansion would be £1.50, 4 kits + 2 expansion would be £3.00 P&P as the expansion boards are the same size and only slightly lighter than the full kits.
Each shipment will contain a printed colour manual.
I have 42 kits/expansion to make up (there's a magic number!) but currently have only enough 10uF poly caps for 24 - rest are on order and will probably take a couple of weeks (from HK)... I have 15 PCBs left from the first run and another 50 on order which should arrive next week.
I'll send out invoices when your bits are ready to ship - USA P&P will be a bit more and overall rate will be converted to USD using XE.COM on the day.
Summary:
P&P within the UK is £1.50 for each multiple of 4 boards of any type (or part thereof), e.g. 2 kits + 2 expansion would be £1.50, 4 kits + 2 expansion would be £3.00 P&P as the expansion boards are the same size and only slightly lighter than the full kits.
Each shipment will contain a printed colour manual.
I have 42 kits/expansion to make up (there's a magic number!) but currently have only enough 10uF poly caps for 24 - rest are on order and will probably take a couple of weeks (from HK)... I have 15 PCBs left from the first run and another 50 on order which should arrive next week.
I'll send out invoices when your bits are ready to ship - USA P&P will be a bit more and overall rate will be converted to USD using XE.COM on the day.
Summary:
- MJSR-KIT : £15.00
- MJSR-EXP : £9.00
- P&P : £1.50 per multiple of 4 boards or part thereof.
Vivitur ingenio, caetera mortis erunt
#124 Re: MJ Statistical Regulator PCBs
Sorry for the delay in responding; vertical for me please.
Ray
Ray
Sorry, I couldn't resist!
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#125 Re: MJ Statistical Regulator PCBs
Ordered 50 PCBs on the 12th December... arrived today....
Good service...
Good service...
Vivitur ingenio, caetera mortis erunt
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#126 Re: MJ Statistical Regulator PCBs
Kits mostly done - just waiting on some more 10uF caps.... 2,100 components into 42 bags... going to have a bit if an argument at the post office as the packets are more than 1 inch thick (because of the big capacitor) so may not count as a letter, thus pushing up p&p...
I need everyone's addresses by PM please (except the original testers) asap.
Ta
I need everyone's addresses by PM please (except the original testers) asap.
Ta
Vivitur ingenio, caetera mortis erunt
- Paul Barker
- Social Sevices have been notified
- Posts: 8863
- Joined: Mon May 21, 2007 9:42 pm
#127 Re: MJ Statistical Regulator PCBs
Might as well pay the extra p and p to be sure because if it gets added at our end it costs more so than if payed correctly in first place, and requires trip to post office where as some folk if they are in to receive the parcel will get it sooner without this extra postage charge (a parsel actually delivered when someone is in that isn't a teenager is an experience I am unfamiliar with)!
Thanks for all your hard work though?
Thanks for all your hard work though?
"Two things are infinite, the universe and human stupidity, and I am not yet completely sure about the universe." – Albert Einstein
#128 Re: MJ Statistical Regulator PCBs
Nick, if anyone falls by the wayside and the opportunity to buy a second kit arises I could use an additional kit or two please.
Thanks
Ray
Thanks
Ray
Sorry, I couldn't resist!
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#129 Re: MJ Statistical Regulator PCBs
I sensibly have a few spare kits from this run - you're currently down for 1V - how many more and what type would you like?
Cheers
BTW. The capacitors from HK arrived just before Christmas, so the kits are now all ready to go...
Cheers
BTW. The capacitors from HK arrived just before Christmas, so the kits are now all ready to go...
Vivitur ingenio, caetera mortis erunt
#130 Re: MJ Statistical Regulator PCBs
Thanks Nick. Please increase my order to two vertical kits.
Ray
Ray
Sorry, I couldn't resist!
#131 Re: MJ Statistical Regulator PCBs
Should I have paid you?jack wrote:...so the kits are now all ready to go...
Ray
Sorry, I couldn't resist!
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#132 Re: MJ Statistical Regulator PCBs
Not yet - should be early next week - I will be stuffing envelopes this weekend and then checking what the postage will be - until I know that I can't issue invoices... I'll just trust youRay P wrote:Should I have paid you?jack wrote:...so the kits are now all ready to go...
I have the following addresses: Steve, Thomas, Ant, Ray, Michael, Dave & TinEar.
I don't seem to have: Simon, Paul, Ali (apologies if I've simply mislaid these)
Could the last three please PM me their mailing address?
Ta!
Vivitur ingenio, caetera mortis erunt
-
- Thermionic Monk Status
- Posts: 5600
- Joined: Thu May 24, 2007 11:22 am
- Location: People's Republic of South Yorkshire
#133 Re: MJ Statistical Regulator PCBs
Just sent you another email Nick. I did sent done before Chrimbo but it must have got lost in the Christmas mail .
Simon.
Simon.
- jack
- Thermionic Monk Status
- Posts: 5493
- Joined: Wed Dec 29, 2010 8:58 pm
- Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
- Contact:
#134 Re: MJ Statistical Regulator PCBs
You should all have emails - packages went out today - 43 boards.
Cheers!
Cheers!
Last edited by jack on Mon Jan 11, 2016 11:19 am, edited 1 time in total.
Vivitur ingenio, caetera mortis erunt
- Dave the bass
- Amstrad Tower of Power
- Posts: 12273
- Joined: Tue May 22, 2007 4:36 pm
- Location: NW Kent, Darn Sarf innit.
#135 Re: MJ Statistical Regulator PCBs
Ta Nick, just sorted your funds, should be with you.
Last edited by Dave the bass on Mon Jan 11, 2016 11:05 am, edited 1 time in total.
"The fat bourgeois and his doppelganger"